Cerámica / vidrio

Base de datos

Material
Aparato
Loading...
 

Contáctenos para una consultación individual.

(2)

  • White Paper: How to minimize standard deviations by correct sample preparation

    Modern analytical methods increase precision and push detection limits to make even the smallest traces of sample components detectable. Despite this development sample preparation, which is carried out prior to the actual analysis, is frequently neglected. Errors caused by lacking accuracy in sample preparation have a much bigger impact than errors made during analysis. Just like an iceberg which is mostly hidden under water, only a small part of the sum of errors is perceived whereas the major part of potential errors is not taken into account (fig. 1). One of the reasons may be the fact that sampling and sample preparation have always been done in a traditional way which has become a routine over the years and is no longer considered as having a critical influence on the subsequent analyses.
  • White Paper: Ultrafine Grinding with Laboratory Ball Mills

    How are nano particles produced? The “Bottom-Up” method synthesizes particles from atoms or molecules. The “Top-Down” method involves reducing the size of larger particles to nanoscale, for example with laboratory mills. Due to their significantly enlarged surface in relation to the volume, small particles are drawn to each other by their electrostatic charges. Nano particles are produced by colloidal grinding which involves dispersion of the particles in liquid to neutralize the surface charges. Both water and alcohol can be used as dispersion medium, depending on the sample material. Factors such as energy input and size reduction principle make ball mills the best choice for the production of nanoparticles.

Informes técnicos (12)

  • Il più puro possibile

    Anche se la macinazione viene svolta in condizioni ideali, gli stress meccanici che il campione esercita sulla superficie degli strumenti di macinazione può causare abrasione. Tuttavia, selezionando un mulino e degli accessori adatti è possibile minimizzare questo effetto. Se il campione deve essere macinato a pezzature inferiori ai 100 microns, le forti forze meccaniche richieste aumentano l’abrasione.
  • La Fragmentación

    Por lo general se asocia a la noción "fragmentación", el machacamiento, de sustancias sólidas mediante fuerza mecánica. Pero también la división de líquidos en gotas o de gases en bollas representa un proceso de fragmentación.
  • La nueva generación de molinas planetarios de bolas

    Los más precisos resultados de trituración en el más breve tiempo se consiguen con los nuevos molinos planetarios de bolas, de Retsch. Con el PM100 y el PM200, Retsch presenta una nueva generación de molinos planetarios de bolas con uno o dos unidades de trituración, que establecen nuevos estándares de rendimiento en este segmento de la producción.
  • Kolloidvermahlungen zur Erzeugung von Nanopartikeln

    Nanoteilchen, d.h. Partikel mit einem Durchmesser von weniger als 100 Nanometer, werden seit vielen Jahren von Wissenschaftlern erforscht. Zum einen lassen sie sich im „Bottom-up“ Verfahren aus Atomen oder Molekülen synthetisieren. Im “Top-Down“ Verfahren hingegen werden größere Partikel, z.B. mit Hilfe von Labormühlen, zerkleinert. Kleine Partikel weisen durch das extrem vergrößerte Verhältnis von Oberfläche zu Volumen erhöhte Oberflächenladungen auf, so dass die Partikel elektrostatisch zueinander gezogen werden. Daher können Nanopartikel nur durch Nassvermahlung (Kolloidvermahlung) erzeugt werden.
  • Sample Division of Large Volumes

    Representative sampling of large sample volumes is an integral part of the physical and chemical analysis of bulk goods and has a decisive influence on the quality of the results. Extraction of a sample from the bulk is not always carried out in a way to ensure representativeness. This is a widespread flaw in the quality control process with a negative impact on the subsequent analysis results. Therefore, more attention should be paid to the correct sampling procedure. Sample division is often considered as a labor-intensive process which not always leads to representative results. RETSCH provides some convenient solutions which help to improve working conditions and thereby the quality of the sampling process.
  • Emax - faster, finer, cooler

    The biggest challenge when developing a high energy ball mill is controlling the temperature. The very high energy produced by ball milling leads to an extreme heat increase inside the grinding jars. RETSCH solved this problem by creating an innovative integrated water-cooling system. Grinding breaks for cooling, which are unavoidable in conventional ball mills even after only 30 minutes grinding at moderate speed, are usually not necessary when using the High Energy Ball Mill Emax.
  • White Paper: Representative Analysis Results Require Adequate Sample Preparation

    A faultless and comparable analysis is closely linked to an accurate sample handling. Only a sample representative of the initial material can provide meaningful analysis results. Rotating dividers and rotary tube dividers are an important means to ensure the representativeness of a sample and thus the reproducibility of the analysis. Correct sample handling consequently minimizes the probability of a production stop due to incorrect analysis results. Thus correct sample handling is the key to effective quality control.
  • Representative sample preparation for XRF analysis

    Preparing homogeneous samples by milling
  • Increasing the development efficiency of ceramic materials

    The development of high-performance ceramics is determined by a large number of influencing factors. In addition to material-specific aspects, such as the chemical purity of the initial raw materials, particle size reproducibility and uniformity of particle morphology, production-specific factors also determine the final properties of ceramics.
  • Representative results require adequate sample preparation

    The following situation is typical for many production plants: After a routine quality check, the production process is stopped or an already produced batch is suspended, because the analysis results were not within the relevant critical values. But does the tested product really deviate from the specifications? The quality control managers are convinced of this because modern analysis instruments provide results with very low tolerances. The sample in question was tested several times and the result was confirmed. The question is why the product does not match the specifications although the production parameters have not been changed in any way.
    The possibility that the tested product is indeed deficient cannot be excluded. However, it is often not the product itself which causes irregular analysis results but a lack of understanding of the steps which come before the analysis.
  • Air Jet Sieving of Bulk Materials

    Particle size analysis and particle size distribution are important criteria for the quality  control of bulk materials. In a running production process, the results of a quality check must be available quickly to allow for immediate adjustment of the production parameters. Depending on the expected particle size and sample volume, different sieving methods and sieving machines are suitable for analysis. The method used for particle size analysis is primarily determined by the fineness of the material to be sieved. For dry sieving of samples with particle sizes below 40 microns, air jet sieving is the method of choice.

Referencias de clientes (2)

Informes de pruebas de laboratorio (35)